| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: mediatek: paris: bypass pinctrl GPIO layer in set GPIO direction
pinctrl_gpio_direction_input() / pinctrl_gpio_direction_output() take
the pinctrl mutex. This causes a gpiochip operations to need to sleep.
Worse yet, the .can_sleep field in the gpiochip is not set. This causes
the shared GPIO proxy to trip over, as it uses gpiod_cansleep() to check
whether it can use a spinlock or needs a mutex. In this case, it ends
up taking a spinlock, then calls pinctrl_gpio_direction_output(), which
takes a mutex. This causes a huge warning.
While this class of Mediatek hardware does not have separate clear/set
registers, the pinctrl context has a spinlock that is taken whenever
a register read-modify-write is done. Also, once the GPIO function is
selected / muxed in, further GPIO operations do not involve pinctrl
operations or state. The GPIO direction and level values do not require
toggling the pinmux or any other pin config options.
Switch to directly calling mtk_pinmux_gpio_set_direction() in the GPIO
set direction callbacks to avoid taking the pinctrl mutex. Drop the
.gpio_set_direction field in mtk_pmxops to signal we are no longer using
the pinctrl GPIO layer for setting the direction. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: phy: check length before parsing PHY status IE
Hardware might report PHY status IE with unexpected length, and parser
might access out of range. Check the length ahead. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: validate and share PSP fw_pri_buf copies via psp_copy_fw
Change psp_copy_fw from void to int: return -ENODEV when drm_dev_enter
fails, and -EINVAL when the image size is zero or larger than the
1 MiB PSP private buffer.
Replace open-coded memset/memcpy into fw_pri_buf with psp_copy_fw. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Bound GPIO I2C table entry count from VBIOS
Reject undersized tables and cap the derived entry count
to AMDGPU_MAX_I2C_BUS so we do not overrun adev->i2c_bus[]
or walk an absurd number of entries on corrupt size fields. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: 8250: protect against NULL uart->port.dev in register
serial8250_register_8250_port() conditionally copies uart->port.dev
from up->port.dev only when up->port.dev is non-NULL:
if (up->port.dev) {
uart->port.dev = up->port.dev;
...
}
So if both the existing uart slot and up have a NULL ->dev,
uart->port.dev remains NULL. The very next ACPI companion check
then dereferences it unconditionally:
if (!has_acpi_companion(uart->port.dev)) {
has_acpi_companion() reads dev->fwnode without a NULL guard
(include/linux/acpi.h), so this NULL-derefs the kernel for the
remaining no-dev case rather than just skipping the
mctrl_gpio_init() initialisation as intended.
smatch flags the inconsistency:
drivers/tty/serial/8250/8250_core.c:767
serial8250_register_8250_port() error: 'uart->port.dev' could be
null (see line 719)
Guard the call with a NULL check so register continues to work
for callers that legitimately have no parent device (legacy
non-OF/non-ACPI registrations).
No functional change for callers that pass a non-NULL ->dev. |
| In the Linux kernel, the following vulnerability has been resolved:
driver core: Avoid warning when removing a device while its supplier is unbinding
During driver removal, the following warning can appear:
WARNING: CPU: 1 PID: 139 at drivers/base/core.c:1497 __device_links_no_driver+0xcc/0xfc
...
Call trace:
__device_links_no_driver+0xcc/0xfc (P)
device_links_driver_cleanup+0xa8/0xf0
device_release_driver_internal+0x208/0x23c
device_links_unbind_consumers+0xe0/0x108
device_release_driver_internal+0xec/0x23c
device_links_unbind_consumers+0xe0/0x108
device_release_driver_internal+0xec/0x23c
device_links_unbind_consumers+0xe0/0x108
device_release_driver_internal+0xec/0x23c
driver_detach+0xa0/0x12c
bus_remove_driver+0x6c/0xbc
driver_unregister+0x30/0x60
pci_unregister_driver+0x20/0x9c
lan966x_pci_driver_exit+0x18/0xa90 [lan966x_pci]
This warning is triggered when a consumer is removed because the links
status of its supplier is not DL_DEV_DRIVER_BOUND and the link flag
DL_FLAG_SYNC_STATE_ONLY is not set.
The topology in terms of consumers/suppliers used was the following
(consumer ---> supplier):
i2c -----------> OIC ----> PCI device
| ^
| |
+---> pinctrl ---+
When the PCI device is removed, the OIC (interrupt controller) has to be
removed. In order to remove the OIC, pinctrl and i2c need to be removed
and to remove pinctrl, i2c need to be removed. The removal order is:
1) i2c
2) pinctrl
3) OIC
4) PCI device
In details, the removal sequence is the following (with 0000:01:00.0 the
PCI device):
driver_detach: call device_release_driver_internal(0000:01:00.0)...
device_links_busy(0000:01:00.0):
links->status = DL_DEV_UNBINDING
device_links_unbind_consumers(0000:01:00.0):
0000:01:00.0--oic link->status = DL_STATE_SUPPLIER_UNBIND
call device_release_driver_internal(oic)...
device_links_busy(oic):
links->status = DL_DEV_UNBINDING
device_links_unbind_consumers(oic):
oic--pinctrl link->status = DL_STATE_SUPPLIER_UNBIND
call device_release_driver_internal(pinctrl)...
device_links_busy(pinctrl):
links->status = DL_DEV_UNBINDING
device_links_unbind_consumers(pinctrl):
pinctrl--i2c link->status = DL_STATE_SUPPLIER_UNBIND
call device_release_driver_internal(i2c)...
device_links_busy(i2c): links->status = DL_DEV_UNBINDING
__device_links_no_driver(i2c)...
pinctrl--i2c link->status is DL_STATE_SUPPLIER_UNBIND
oic--i2c link->status is DL_STATE_ACTIVE
oic--i2c link->supplier->links.status is DL_DEV_UNBINDING
The warning is triggered by the i2c removal because the OIC (supplier)
links status is not DL_DEV_DRIVER_BOUND. Its links status is indeed set
to DL_DEV_UNBINDING.
It is perfectly legit to have the links status set to DL_DEV_UNBINDING
in that case. Indeed we had started to unbind the OIC which triggered
the consumer unbinding and didn't finish yet when the i2c is unbound.
Avoid the warning when the supplier links status is set to
DL_DEV_UNBINDING and thus support this removal sequence without any
warnings. |
| In the Linux kernel, the following vulnerability has been resolved:
virt: acrn: Fix irqfd use-after-free during eventfd shutdown
acrn_irqfd_deassign() and the eventfd EPOLLHUP wakeup can race and free
the same struct hsm_irqfd:
CPU0 CPU1
---- ----
eventfd_release()
wake_up_poll(EPOLLHUP)
hsm_irqfd_wakeup()
queue_work(&irqfd->shutdown)
acrn_irqfd_deassign()
hsm_irqfd_shutdown()
list_del_init()
eventfd_ctx_remove_wait_queue()
eventfd_ctx_put()
kfree(irqfd)
hsm_irqfd_shutdown_work()
container_of(work, ..., shutdown)
irqfd->vm <-- use-after-free
The deassign path freed the irqfd while a shutdown work item was
already queued by EPOLLHUP (or vice versa), so the work item could
resurrect a dangling pointer through container_of().
Switch to the lifetime model used by KVM irqfds:
- Deassign/deinit only deactivate the irqfd: remove it from vm->irqfds
under irqfds_lock and queue the cleanup work.
- hsm_irqfd_shutdown_work() becomes the sole owner that unhooks the
eventfd waitqueue entry, drops the eventfd reference and frees the
irqfd.
- A new HSM_IRQFD_FLAG_SHUTDOWN bit guarded by test_and_set_bit()
ensures the cleanup work is queued at most once, no matter how many
of {EPOLLHUP, deassign, deinit} fire concurrently. This is safe to
call from the waitqueue callback, which runs with wqh->lock held and
IRQs disabled and therefore cannot take irqfds_lock.
- acrn_irqfd_deassign() flushes vm->irqfd_wq before returning so the
eventfd is fully detached on return. acrn_irqfd_deinit() deactivates
every irqfd, flushes the workqueue and only then destroys it, so no
path can queue_work() onto a torn-down workqueue.
- acrn_irqfd_assign() now installs the eventfd waitqueue entry and
publishes the irqfd to vm->irqfds under irqfds_lock, so the irqfd is
never visible to deassign/deinit before its waitqueue entry is in
place, and any EPOLLHUP that fires in the assign window queues
cleanup work that blocks on irqfds_lock until publication is done. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/counter: Fix num_counters leak on bind_qp failure in alloc_and_bind()
When __rdma_counter_bind_qp() fails in alloc_and_bind(), the error path
jumps to err_mode which frees the counter without decrementing
port_counter->num_counters. The only place that decrements is
rdma_counter_free(), which is unreachable since the counter was never
successfully bound.
This leak accumulates across repeated failures, permanently preventing
the port from switching to AUTO mode (-EBUSY in __counter_set_mode())
and blocking the MANUAL→NONE auto-revert in rdma_counter_free(). When
the mode was NONE before the call, the MANUAL mode set by
__counter_set_mode() also leaks since the revert logic is never
reached.
Add an err_bind label between the num_counters increment and the
existing err_mode label. It decrements num_counters and mirrors the
MANUAL→NONE revert from rdma_counter_free(), ensuring the port state
is fully restored on bind failure. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix buffer overflow during vBIOS update
Clamp the buffer postion to write by setting the bin attribute
to the maximum buffer size so that VFS layer will block the
out-of-bounds accessing. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: fix SMI event cross-process information leak
kfd_smi_ev_enabled() skips the suser privilege check when pid=0.
PROCESS_START, PROCESS_END, and VMFAULT events are emitted with
pid=0 while carrying another process's PID and command name, so any
/dev/kfd user in the render group can monitor all GPU workloads.
Pass the target process PID into kfd_smi_event_add() for these events
so the existing per-client filter restricts delivery to the owning
process or CAP_SYS_ADMIN subscribers. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-fc: Do not cancel requests in io target before it is initialized
A new nvme-fc controller in CONNECTING state sees admin request timeout
schedules ctrl->ioerr_work to abort inflight requests. This ends up
calling __nvme_fc_abort_outstanding_ios() which aborts requests in both
admin and io tagsets. In case fc_ctrl->tag_set was not initialized we
see the warning below. This is because ctrl.queue_count is initialized
early in nvme_fc_alloc_ctrl().
nvme nvme0: NVME-FC{0}: starting error recovery Connectivity Loss
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
lpfc 0000:ab:00.0: queue 0 connect admin queue failed (-6).
you didn't initialize this object before use?
turning off the locking correctness validator.
Workqueue: nvme-reset-wq nvme_fc_ctrl_ioerr_work [nvme_fc]
Call Trace:
<TASK>
dump_stack_lvl+0x57/0x80
register_lock_class+0x567/0x580
__lock_acquire+0x330/0xb90
lock_acquire.part.0+0xad/0x210
blk_mq_tagset_busy_iter+0xf9/0xc00
__nvme_fc_abort_outstanding_ios+0x23f/0x320 [nvme_fc]
nvme_fc_ctrl_ioerr_work+0x172/0x210 [nvme_fc]
process_one_work+0x82c/0x1450
worker_thread+0x5ee/0xfd0
kthread+0x3a0/0x750
ret_from_fork+0x439/0x670
ret_from_fork_asm+0x1a/0x30
</TASK>
Update the check in __nvme_fc_abort_outstanding_ios() confirm that io
tagset was created before iterating over busy requests. Also make sure
to cancel ctrl->ioerr_work before removing io tagset. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix races in cifsd thread creation
The cifsd demultiplex thread can run and access tcp_ses before the parent
thread has finished populating tcp_ses, which the worker thread accesses
locklessly.
Also, the kthread_run macro may start the thread before returning the
thread pointer. Because the pointer is part of the structure that the
thread can access, if the kernel is preempted after the thread is spawned,
but before the thread pointer is populated and the thread attempts to exit,
it will sleep, waiting for a SIGKILL signal.
Fix this by moving creation of the thread to after all of tcp_ses'es
fields are populated, and spawning the thread last, using a split
kthread_create/wake_up_process logic. |
| In the Linux kernel, the following vulnerability has been resolved:
exfat: fix handling of damaged volume in exfat_create_upcase_table()
When the size of the upcase table is set to zero in the dentry for any
reason(e.g. corrupted media or misbehaving device), an integer overflow
causes the module to loop indefinitely.
If the size of the upcase table is read zero, do not attempt to load the
table. Instead, fallback to loading the default upcase table. If the
size of the upcase table is zero or no upcase table is found, raise
exfat_fs_error() to mark the volume read-only. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Let driver decide buffer size at AMDKFD_IOC_GET_DMABUF_INFO ioctl
amdkfd driver needs allocate buffer to return bo metadata to user space. The
buffer size is controlled by user currently. It is a potential security issue
that hostile value (e.g. 2 GiB) lets any render-group user trigger order-MAX
allocation/OOM in kernel context.
This patch first finds bo metadata size. If the size is smaller than user
provided value drive can safely allocate buffer in kernel space and copy to
user space buffer. If not, driver will let user know, not allocate and copy.
User will redo with new buffer in user space.
This patch lets driver decide buffer allocation size to avoid potential hostile
size from user space.
(cherry picked from commit f54ce9e8cbd3abe0eda3a285f54dc4f572fe589a) |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix addr_filter_ranges lifetime
Lee Jia Jie reported that since event::addr_filter_ranges is used
under RCU, it should be RCU freed. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: ibss: wait for in-flight TX on disconnect
While leaving an IBSS in ieee80211_ibss_disconnect() mac80211 flushes
stations, turns the carrier off and immediately tells the driver to
leave as well. While there may be synchronize_net() in station flush
and in this code later, packets can still be transmitted due to
cross-CPU race conditions after carrier off is set.
Therefore, it's possible for a race to happen where a TX to the
driver occurs while or after telling it to leave the IBSS. This can
be confusing to drivers, and in the case of iwlwifi leads to an
attempt to use invalid queues.
Move netif_carrier_off() to occur before sta_info_flush() during
IBSS disconnect, and add synchronize_net() if flushing didn't,
so that the synchronize_net() always happens between turning the
carrier off and telling the driver, avoiding this race. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: pcie: null RX pointers after free
When iwl_pcie_tx_init() fails after RX init, nic init unwinds via
iwl_pcie_rx_free().
The freed RX members stayed non-NULL on the live transport object,
so later teardown or retry could touch stale RX state.
Set rx_pool, global_table, rxq, and alloc_page to NULL after free
to make repeated cleanup and retry paths safe. |
| In the Linux kernel, the following vulnerability has been resolved:
smb/client: flush dirty data before punching a hole
Punching a hole after a large buffered write may leave the range
reported as data. Reproduce it with:
xfs_io -f \
-c "pwrite -b 3m -S 0x61 0 3m" \
-c "fpunch 1m 1m" \
-c "seek -h 0" \
-c "seek -d 1m" \
/mnt/test/repro
Punching 1 MiB at offset 1 MiB should produce:
0 1 MiB 2 MiB 3 MiB
| DATA | HOLE | DATA | EOF
Instead, the entire file is reported as data. SEEK_HOLE(0) returns EOF,
and SEEK_DATA(1M) returns 1M.
This happens because a dirty folio spanning the punched range can be
written back after the punch and refill the hole.
Fix this by flushing and waiting for dirty data in the punched range
before invalidating the page cache and issuing FSCTL_SET_ZERO_DATA.
The xfstests generic/539 pass against Samba/ksmbd with this change. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: validate TX_CMD response layout
TX_CMD parsing uses frame_count to walk status entries and then
read the trailing SCD SSN. Make the minimum-length check follow
that exact runtime layout calculation before parsing the payload.
For new TX API, reject TX_CMD responses with frame_count != 1 and
warn/return in the aggregation handler to document that aggregated
accounting is expected via BA notifications. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: fix a possible underflow
We shouldn't trust the firmware about the length of the wowlan packet. |
